Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTrusted Shingle, Tile & Metal Roofing for Coral Springs Homeowners
Coral Springs roofing has one job above all others: keep the afternoon thunderstorms and the July sun from getting inside your house. Shingle, tile, and metal roofing in Coral Springs each handles that job differently, and most roofs fail not because the material wore out, but because it was installed out of true, with the wrong underlayment, or with flashing that never got a second look. We’ve been setting roofs right since 2008 across Coral Springs, and a live person answers our phone at (727) 261-2215 every time you call.
Dale Kessler started TruePane in 2008 on a rule he still keeps on the whiteboard: if the pane is not true, the job is not done. That rule fits roofing just as well. We measure twice, quote manufacturer lines side by side on paper, and register both warranty layers in writing before our truck leaves your driveway. Whether you’re in the Windings, Cypress Glen, or the neighborhoods off Wiles Road, we show up when we say we will and do the work right the first time.
What Our Shingle, Tile & Metal Roofing Service Includes
Asphalt Shingle Roofing
Asphalt shingles are the most common roof in Coral Springs, and the most commonly misjudged. A shingle roof failure usually starts small: a lifted edge near a valley, a nail that missed its mark, a ridge cap that shifted just enough to let the afternoon storm find a way in. When we install shingles, we replace the entire underlayment and flashing system, not just the visible layer, because the shingle is only as good as what sits beneath it. Our job is a shingle roof that stays sealed against wind-driven rain, lays flat across every plane, and drains cleanly at every edge.
We install architectural and designer shingle lines from manufacturers we trust, and we stock matching components so patch jobs don’t end up looking like patch jobs. If you have an older three-tab roof in Coral Springs that has started to curl or granulate, we can tell you honestly whether a repair will hold or whether a full replacement is the square deal. The answer never includes a surprise line item.
Every shingle roof we install gets the TruePane treatment: both warranty layers registered in writing, durations stated, and a Done Right Promise on the workmanship. We stand behind it. No paperwork fights, no arguing.
Tile Roofing
Tile roofs are common in Coral Springs because they hold up to the sun and the rain, but they are heavier than shingles and far less forgiving of sloppy flashing work. A cracked tile or a slipped tile is not always the real problem; the real problem is often the underlayment beneath it, or a valley that was never flashed to the pitch of the roof. We inspect tile roofs the way a glazier inspects a frame: we check for what you can see and what you cannot.
When we repair tile roofs in Coral Springs, we match the tile profile and color where possible, and we re-bed the ridge and hip tiles with mortar mixed for Florida humidity so it bonds and stays bonded. When we replace a tile roof, we start from the deck up: new underlayment, new battens where the profile calls for them, new flashing at every penetration, and tiles set straight and locked. A tile roof done right sheds water quietly for decades.
Homeowners in Coral Springs with older tile roofs should have them looked at after any serious storm, especially around chimneys, skylights, and pipe boots. We’ll give you a straight answer about what needs attention now and what can wait. We measure every opening twice, and we treat your roof the same way.
Metal Roofing
Metal roofing in Coral Springs has become more common as homeowners look for something that will outlast the next two or three shingle cycles. Standing seam and metal shingle systems handle the tropical sun better than almost anything else, but they only work if the fasteners, clips, and flashings are right. Metal expands and contracts with the heat, and a panel that was over-driven or under-driven will telegraph its mistake as an oil-can dent or a leak at the seam within a few seasons.
We install metal roofing with the right clip and fastener system for the specific panel profile, and we flash every transition with metal-to-metal details that move when the roof moves. That’s the difference between a metal roof that lasts forty years and one that starts leaking in three. We also service existing metal roofs: re-torquing fasteners, replacing worn panel screws, and sealing joints with product approved for the system.
If you’re weighing metal against shingle or tile, we’ll show you numbers on paper for each line we carry. You can see the material cost, the labor, and the warranty duration for each option before you decide. No pressure, no canned pitch. That’s a square deal.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Shingle, Tile & Metal Roofing
We work on roofing systems from a range of manufacturers, and we have specific experience with the lines that show up most often in Coral Springs. With CGI roofing products, we’ve handled both the panel installation and the trim and flashing details that make the difference between a roof that looks right and one that is right. CGI metal profiles demand precise fastener placement, and our background-checked technicians have set enough of them to know exactly what over-torquing sounds like and how to avoid it.
With ES Windows and ECO Window Systems we’ve spent years managing glazing and opening details, and that matters on roofs because skylights, solar tubes, and roof-to-wall transitions are where most roof warranties die. The same technician who knows how to flash a window properly knows how to flash a roof penetration so it will not leak. Whether you have one of those brands or any other make, we can service it and we’ll tell you straight what parts need replacing and what does not. If you have a different brand altogether, ask us. We can help with most major manufacturers.
Signs You Need Shingle, Tile & Metal Roofing Right Now
- Water stains on the ceiling after rain. A stain is not a small problem. It means water has already made it through the roof deck and is working on the drywall. By the time you see the stain, the leak has usually been running for a while, and mold may be building in the cavity. Call us before the next storm; we’ll trace the water to its source, not just patch the stain.
- Granules in the gutter or at the downspout. Asphalt shingles shed their mineral granules as they approach the end of their life. If you’re seeing dark sand collecting at the gutter outlet, your shingles are losing their UV protection and the mat is starting to bake. That’s the early warning that a Coral Springs roof replacement is in your near future, and pricing it now costs less than pricing it after a failure.
- Cracked, slipped, or missing tiles. One broken tile after a storm is usually a repair. A pattern of cracked tiles across the roof, especially on the south and west exposures, is how tile roofs signal that the underlayment has aged and the tile is no longer protecting it. A tile that has slipped out of position leaves a direct path for wind-driven rain to reach the deck. We’ll tell you honestly whether you need a repair or a full re-roof.
- Metal panels that rattle in the wind or show oil-canning. Fasteners that have backed out make metal roofs rattle, and each loose fastener is a potential entry point for water. Oil-canning is the wavy distortion that happens when a panel is stressed by heat expansion or an undersized clip system. Both are fixable if caught early; both get worse every season they’re ignored.
- Flashing that has pulled away from the chimney, walls, or pipes. Flashing is the most common leak point on every roof type. In Coral Springs, the heat and humidity cause sealants to dry and split, and the flashing lifts. A lifted flashing lets water run directly onto the deck, and the leak often shows up far from the actual opening. That’s why we inspect every flashing point during a tune-up, not just the ones that look bad from the ground.
Our Shingle, Tile & Metal Roofing Process - Step by Step
- 1
Free on-site assessment and written quote. We send a background-checked, uniformed technician to walk your roof, measure the openings, and check the deck, underlayment, and flashing conditions. You get a line-item quote on paper, so you know exactly what you’re buying and why. No verbal estimates that change later.
- 2
Material selection and side-by-side comparison. We show you manufacturer lines side by side, with the warranty duration stated for each. You choose the system that fits your house and your budget. We do not push the most expensive line; we show you what each one costs and what you’re getting for it.
- 3
Permit and site preparation. We pull the permits for your roofing project in Coral Springs and schedule the work with the city’s requirements in mind. Our team covers landscaping, protects windows and doors, and sets up so your home stays clean and safe during the job.
- 4
Installation with precise fastening and flashing. Every panel, shingle, or tile is set to manufacturer specification, with fasteners driven to the correct depth and flashing details built to move with the roof. We inspect underlayment seams, valley transitions, and every penetration before we call the roof done.
- 5
Final inspection and warranty registration. We walk the roof with you if you’d like, and we register both layers of warranty in writing before the truck leaves. Our Done Right Promise is on the paperwork. If it is not done right, we make it right. No arguing.
How Much Does Shingle, Tile & Metal Roofing Cost in Coral Springs?
A typical asphalt shingle roof replacement in Coral Springs runs $7,500 to $14,000 for an average single-story home, depending on the pitch, the number of valleys, and the shingle line you choose. Tile roof replacement generally starts around $18,000 and can run well into the $30,000 range for larger or more complex roofs, because tile is heavier and the underlayment and flashing details take longer to do correctly. Metal roofing falls between $16,000 and $28,000 for most Coral Springs homes, depending on the panel profile and the roof geometry. Repair work is priced differently: a small shingle repair may run $350 to $750, a tile replacement repair $400 to $900 depending on access, and a metal fastener service $300 to $600.
What moves the price is the condition of the existing deck, the number of roof penetrations that need flashing, the height and pitch of your roofline, and whether you want the old roof torn off or can roof over it. Coral Springs code and good practice both say a roof over a roof is a compromise you should only choose when the deck is clean and dry, and that’s rare. Watch for bids that skip the underlayment replacement or use a lighter underlayment than the manufacturer specifies: those are the “cheap in the front, expensive later” bids that leave you with a leak and no warranty.
Our free estimate includes the whole picture: deck condition, flashing replacement, underlayment, materials, labor, permits, and cleanup. We give you the number in writing before you commit to anything. Call (727) 261-2215 to schedule a free estimate, and we’ll walk your roof with you and show you what we see.
Shingle, Tile & Metal Roofing Near Coral Springs - Our Service Area
We serve Coral Springs and the surrounding communities, including Shingle, Tile & Metal Roofing in Margate, Shingle, Tile & Metal Roofing in Parkland, Tamarac, Coconut Creek, North Lauderdale, Sunrise, and Pompano Beach. Most roofing assessments in Coral Springs can be scheduled within a few days, and we always confirm the appointment time. If you’re in one of the nearby cities and want to know whether your roofing issue needs urgent attention, call our home office and a live person will talk it through with you right then.
Serving Coral Springs, FL - Our Local Coverage Area
We’re based in the Coral Springs area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Shingle, Tile & Metal Roofing in Coral Springs
Shingle, tile, and metal roofing service means installing, repairing, replacing, and maintaining the three most common roof systems in Coral Springs: asphalt shingles, concrete or clay tile, and standing seam or metal shingle panels. Each system has its own fastening pattern, flashing requirements, and failure modes, and we handle all three rather than specializing in just one and guessing at the others. The service includes full replacements, component repairs, storm damage assessment, and warranty registrations handled in writing before our truck leaves your property.
Most asphalt shingle replacements in Coral Springs are completed in two to four days, depending on the roof size and pitch. Tile roof replacements typically take five to eight days because tile setting is slower and the underlayment installation is more detailed; metal roofs fall somewhere in the middle at three to six days. Weather in South Florida can stretch a schedule, and we’ll tell you at the outset what the realistic timeframe looks like for your specific roof. Call (727) 261-2215 and we’ll give you an honest schedule for your house.
A new shingle roof in Coral Springs typically runs $7,500 to $14,000 depending on size and shingle line. Tile roofs run higher, generally $18,000 to $30,000 or more, because the materials are heavier and the installation is more labor-intensive. Metal roofs usually run $16,000 to $28,000 for a typical home. The exact number depends on your roof’s footprint, pitch, existing deck condition, and the system you select; a free written estimate from us shows the line-item detail so you can see exactly where the money goes. Call for a free estimate and you’ll have the number in writing, no obligation.
Yes, we service CGI metal roofing systems, and our glazing background gives us specific expertise with ES Windows and ECO Window Systems skylight and roof-penetration details. The flashing where a roof meets a skylight or a vertical wall is where most roof warranties die, and that happens to be exactly what a glazier-trained technician understands best. If you have a different brand, ask us; we work with most major manufacturers and will tell you straight whether we can properly service your system before any work begins.
We offer prompt storm damage response in Coral Springs. If a tree branch has punctured your roof or wind has torn away shingles or tiles, call (727) 261-2215 and a live person answers the phone 24 hours a day, 7 days a week. We will talk through what you’re seeing, advise you on temporary protection if it is safe to do so, and get a technician to your house to assess the damage and provide a written repair quote.
Every roofing installation or replacement we do is covered by our Done Right Promise and The Keystone Standard. That means both manufacturer warranty layers are registered in writing, with their durations stated, before our truck leaves your driveway. The manufacturer covers the material, and our workmanship promise covers the installation. If something is not done right within the 90-day window, we make it right. No paperwork fights, no arguing. We stand behind it.
Before we start, we’ll walk you through what to expect: how we’ll protect your landscaping, where we’ll stage materials, and how we’ll manage debris removal. Inside the house, you’ll want to clear items from the attic floor near the roofline, and it helps to move vehicles out of the driveway so we can work without obstruction. The biggest thing you can do is choose a contractor who answers the phone when you call and shows up when they say they will. The rest is our job to handle.
Schedule Your Shingle, Tile & Metal Roofing Service in Coral Springs Today
If your roof is showing its age or you want a professional assessment before the next storm season, call (727) 261-2215 today. The estimate is free, the quote is on paper, and the work is done right. A live person answers every call, 24 hours a day, so you’ll never get a voicemail tree. We’ll show up when we say we will and we’ll stand behind the work in writing.
Written by Dale Kessler, Owner at TruePane Windows & Doors, serving Coral Springs since 2008.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.