PGT Shingle, Tile & Metal Roofing Nationwide | TruePane Windows & Doors

PGT Shingle, Tile & Metal Roofing in Coral Springs: What to Know First

We provide independent PGT shingle, tile and metal roofing service in Coral Springs, with most repairs and replacements completed on a schedule we put in writing before work begins. The honest price posture is this: a straightforward PGT roof repair in Coral Springs typically runs $425 to $1,850 depending on the product line, the failure, and whether we’re matching tile profiles or ordering a specific PGT metal profile. A full shingle, tile or metal roofing replacement on a PGT system is a larger job, and we quote it line by line so you see exactly what you’re paying for. This page is written for Coral Springs homeowners who own PGT products and want the work done right the first time, with both warranty layers registered in writing. If you’d rather talk it through, call (727) 261-2215 and a live person answers.

Call (727) 261-2215

How PGT Products Fail - and How We Fix Them

• PGT WinGuard shingle underlayment separation at flashing points. We see this on Coral Springs homes where the original flashing was set against PGT’s heavier-gauge framing and the seal breaks at the corners first. The shingle looks fine from the ground, but water gets in at the transition. We remove the affected shingles, reset the flashing to PGT’s profile, and reseal the underlayment before reinstalling. Done right, it won’t weep in the next storm.
• PGT WinGuard tile profile mismatch after a patch job. This happens when a handyman or a roofer who doesn’t carry PGT tile profiles slaps in a close-enough tile. It binds at the interlock, water pools behind it, and the tile cracks at the nail line within a season or two. We order the matching PGT profile and set the replacement so it interlocks clean. No caulk-and-hope fix.
• PGT metal roof panel oil-canning and fastener backout on exposed trim. Coral Springs heat cycles do this to metal panels that weren’t lapped with enough room for expansion. The panel warps slightly, the fasteners start to back out, and you hear it rattle in the wind. We pull the affected trim, re-lap the panel, and reset with the right fasteners and neoprene washers rated for coastal Florida humidity. The panel lays flat again and stays quiet.
• PGT shingle granule loss concentrated at one slope. If granule loss is on a single slope and the roof is under fifteen years old, it’s rarely the shingle failing. It’s usually a gutter or downspout issue causing water to wash over the shingle surface at volume. We fix the drainage first, then replace only the shingles that lost granule. You don’t pay for a tear-off when the slope is the problem.
• PGT tile valley leaks that three other roofers “fixed” with sealant. The valley wasn’t flashed to PGT’s tile profile, and someone kept pumping sealant into the gap. Sealant fails in Coral Springs sun. We pull the tile, replace the valley metal with the correct width for the PGT profile, and reset the tile on a clean plane. The leak stops because the water goes where the roof was designed to send it.

Our PGT Shingle, Tile & Metal Roofing Process

Here’s how a typical PGT roof job runs with us:

1. 1
   You call (727) 261-2215. A live person answers. We set a time and we show up when we say.
2. 2
   We walk the roof and the attic. We look at the PGT product, how it was set, how it’s draining, and what’s happening underneath. We read the rough opening before we quote it, which is why our change-order rate is low enough to count on one hand.
3. 3
   We quote on paper, line by line. If it’s a PGT shingle repair, we tell you which slope, how many squares, and what the material cost is. If it’s tile, we specify the profile. If it’s metal, we spec the panel and fastener.
4. 4
   We order PGT-matched or OEM parts where they matter. For warranty-safe work, we use OEM or exact-profile replacement. If a quality aftermarket part is functionally identical and saves you money, we tell you that on the quote and let you decide.
5. 5
   We do the work, register the warranties, and check our own work. Both warranty layers get registered in writing before our truck leaves the driveway. If anything isn’t done right, the Done Right Promise means we come back and make it right.

What PGT Shingle, Tile & Metal Roofing Costs in Coral Springs

Here are the numbers we see most often in Coral Springs:

• PGT shingle repair (flashing, granule loss, small leak): $425 to $780
• PGT tile replacement (profile-matched, several tiles plus valley or flashing work): $680 to $1,450
• PGT metal roof repair (panel reset, fastener replacement, trim): $550 to $1,850
• Full PGT shingle, tile or metal roofing replacement: quoted line by line, never as a round number with a handshake

What moves the price: roof pitch, access, how many layers are coming off, whether we’re matching tile profiles or ordering PGT metal panels, and whether the decking underneath has rot from a long-running leak. We don’t pad the quote for “just in case.” We quote what we see, and when we open it up and find something we couldn’t see, we call you before we do anything. For an exact number on your PGT roof in Coral Springs, call (727) 261-2215 for a free estimate.

Why Coral Springs Homeowners Call TruePane Windows & Doors for PGT Work

Dale Kessler grew up in the Ramblewood neighborhood of Coral Springs and has been measuring, setting and trimming impact windows and exterior doors across Broward County for the better part of two decades. He knows PGT products because he’s set them, repaired them, and watched how they age in this specific climate. Our technicians are background-checked and uniformed, and they work in your home the way they’d work in their own mother’s house. We also service CGI, CWS, ES Windows and ECO Window Systems products, so if you have a mixed-brand house with PGT in one section and something else in another, one call handles all of it. Every job carries the Done Right Promise, and both warranty layers are registered in writing before the truck leaves your driveway. We stand behind it.

FAQs