CWS Custom & Geometric Windows Nationwide | TruePane Windows & Doors

CWS Custom & Geometric Windows in Coral Springs: What to Know First

TruePane Windows & Doors is an independent CWS service provider in Coral Springs, and we handle custom and geometric CWS windows that most contractors won’t touch: arched tops, radius corners, trapezoids, octagons, and oversized openings. A typical CWS custom window service call in Coral Springs runs $185 to $420 for a repair, while full custom replacements on shaped openings usually land between $900 and $2,800 depending on glass, frame, and geometry. We quote line-by-line, in writing, before any work begins, and we register both warranty layers before the truck leaves your driveway. If you have a CWS geometric window that’s fogged, binding, or leaking, call (727) 261-2215 and we’ll walk you through what you’re likely dealing with.

Call (727) 261-2215

This page is for Coral Springs homeowners who own CWS windows with custom shapes or non-standard geometry. If your window isn’t a stock rectangle, the rules change. We’ll explain what that means for repairs, parts, and pricing, and where CWS products tend to fail in South Florida’s climate.

How CWS Products Fail - and How We Fix Them

• Radius and arched CWS units lose their seal at the apex first. The bend in the glass puts constant stress on the sealant at the highest point of the curve. In Coral Springs, where afternoon heat pushes surface temperatures past 140 degrees on south-facing walls, that stress shortens the seal life noticeably. We see arched CWS units in the Cypress Run and Shadow Wood neighborhoods fog at the crown while the straight legs stay clear. The fix is a full IGU replacement cut to match the radius exactly, not a “close enough” rectangular glass wedged into a curved frame. We template every arch from the actual opening, not from a spec sheet.
• CWS trapezoid and pentagon windows in gable ends develop frame racking that binds the sash. Triangular and five-sided units carry wind load differently than rectangles. On second-story gables in the Kensington and Turtle Run areas, the constant push from afternoon easterly breezes works the frame corners loose over a decade. A binding CWS geometric window usually isn’t a bad operator, it’s a frame that’s out of square. We measure the opening diagonally before we quote, and we reset the frame before we install anything new. Dale Kessler’s rule applies here: measure it right the first time, and the rest of the job takes care of itself.
• CWS impact geometric windows can pass a visual check and still fail the water test. Shaped impact glass relies on the frame seal more heavily than a rectangular unit because there’s more linear foot of edge relative to glass area. We’ve pulled CWS half-moon transoms in Coral Springs where the glazing looked fine but water had been wicking behind the frame for two seasons. By the time the homeowner saw the drip, the rough opening was already spongy. We don’t replace a CWS impact window without checking the rough opening for moisture damage behind the frame.
• Oversized CWS fixed picture windows and quarter-rounds crack from poor header support, not glass defects. A big geometric window over a sliding door or in a two-story foyer carries weight from above if the header was undersized. Coral Springs homes built in the 1980s and early 1990s sometimes have headers on custom openings that were marginal from day one. The glass cracks when the header sags a quarter inch and transfers load to the frame. We inspect for this before ordering replacement glass because putting new glass into a sagging opening just means you’ll be calling us again in three years.
• CWS corner windows with mitered glass joints delaminate at the seam in humid months. CWS corner units that meet at a 90-degree mitered glass corner without a vertical frame member are beautiful, and they’re also the most humidity-sensitive window geometry in South Florida. The sealant at the miter expands and contracts at a different rate than the glass. June through September in Coral Springs is when we get most of these calls: fogged corner seams, or a subtle drip at the miter after a hard afternoon storm. The repair is a full replacement of the corner unit with proper miter sealant rated for South Florida humidity swings.

Our CWS Custom & Geometric Windows Process

Here’s how a CWS custom or geometric window job works with us, from your first call to the final walkthrough:

1. 1
   You call (727) 261-2215 and talk to a person. No voicemail tree. We ask what you’re seeing: fog, water, a bind, a draft. We can usually give you a rough idea of what you’re dealing with over the phone.
2. 2
   We measure the opening, not the old glass. Dale Kessler reads every rough opening before he quotes. For shaped CWS windows, we make a physical template of the arc or angle. Spec-sheet measurements on ten-year-old CWS installs are often off by an eighth of an inch or more, and on a radius window, an eighth-inch error can mean a $900 piece of glass that doesn’t fit.
3. 3
   We price the job in writing, line by line. You’ll see the glass cost, frame work, sealant, labor, and disposal broken out. If we need a CWS-specific part, we’ll quote it as OEM and give you the aftermarket option if one exists and is worth your money. Some CWS parts must come from CWS distribution; we’ll tell you when that’s the case and what the lead time actually is.
4. 4
   We do the work once. Pull the old unit, repair or replace the frame, reset the rough opening as needed, install the new glass or window, and seal it with materials rated for what Coral Springs weather does to a building in August.
5. 5
   We test before we leave. Water test on every exterior install. Operate every sash. Check the reveal. If the pane is not true, the job is not done.
6. 6
   We register both warranty layers in writing before the truck leaves your driveway. You get the duration and terms for the glass, the frame, and our Done Right Promise. No fine print that covers neither.

What CWS Custom & Geometric Windows Costs in Coral Springs

Here’s what you should expect to pay for common CWS work in Coral Springs. These are real ranges from jobs we’ve done in the area, not national averages:

• Reseal a CWS arched or radius window: $185 to $420, depending on elevation and access.
• Replace a fogged IGU in a CWS half-moon or quarter-round: $450 to $1,100, depending on size and whether the glass is impact-rated.
• Full replacement of a CWS trapezoid or pentagon window: $900 to $2,200 for a standard vinyl frame with non-impact glass; $1,500 to $2,800 for impact glass.
• Replace a CWS mitered corner window: $1,800 to $3,500, because the corner unit is two pieces of glass joined at a structural seam and the fabrication is more involved.
• Restore and reset a CWS oversized fixed picture window with header repair: $1,200 to $2,400, not including any structural header work if the opening needs it.

What moves the price: whether the glass is impact-rated, whether your HOA requires a specific frame finish or tint, whether the window is on a second story, and whether the rough opening needs structural repair before new glass goes in. We quote this all upfront, and we don’t add change orders after the job starts unless we find rot or structural issues behind the frame that couldn’t be seen until we opened the wall.

Call (727) 261-2215 for an exact quote on your CWS window. Estimates are free, and you’ll get pricing in writing before you commit to anything.

Why Coral Springs Homeowners Call TruePane Windows & Doors for CWS Work

We’ve been serving Coral Springs and Broward County since 2008, going back to when Dale Kessler was resealing jalousie windows in his dad’s Ramblewood house every summer. The company has been TruePane since 2008, but the habit is older than that: do the job right, write down what you promised, and answer the phone when the customer calls back.

The Done Right Promise is a real guarantee. If something isn’t right, we make it right. No paperwork fights, no arguing. The Keystone Standard means both warranty layers are registered in writing before our techs pull out of your driveway. And because CWS is no longer the dominant line in every Coral Springs neighborhood, it matters that we’re authorized installers for more than a dozen manufacturers, including PGT, CGI, ES Windows, and ECO Window Systems. If your CWS geometric window is beyond a sensible repair, we can quote you side-by-side options in writing so you can compare what a replacement actually costs across brands, not just what one manufacturer’s brochure says.

A live person answers our phone 24 hours a day. Our techs are background-checked and uniformed. We work in your home the way we’d work in our mother’s. That’s the standard, and it doesn’t change because a window has six sides instead of four.

FAQs