Therma-Tru Shingle, Tile & Metal Roofing Nationwide | TruePane Windows & Doors

Therma-Tru Shingle, Tile & Metal Roofing in Coral Springs: What to Know First

We’re an independent Therma-Tru service provider in Coral Springs, and we handle shingle, tile, and metal roofing work on Therma-Tru door and window systems that have been compromised by roof failures, flashing problems, or water intrusion around the roofline. Most Therma-Tru roofing-related repairs in Coral Springs take us one to two visits: the first to diagnose and quote, the second to complete the work once parts are in hand. Our pricing is fixed and written down before we start, not after we open the wall.

Call (727) 261-2215

If you own a Therma-Tru entry door or window system in Coral Springs and you’ve noticed water staining, a door that binds, or flashing that’s pulling away from the roofline, this page is for you. Call (727) 261-2215 and a live person answers, day or night.

How Therma-Tru Products Fail - and How We Fix Them

Therma-Tru builds a solid door, but doors and windows are only as dry as the roof and flashing above them. Here’s what we see in Coral Springs homes, and what we do about it.

• Fiber-Classic and Smooth-Star entry doors with rotted bottom rails. In Coral Springs, afternoon thunderstorms push water sideways against south-facing entryways. When the threshold flashing wasn’t lapped correctly under the door pan, water wicks up into the bottom rail. We pull the door, replace the rot-damaged rail with an OEM-grade replacement, and re-flash the pan so water sheds away instead of pooling under the slab.
• Benchmark door units with failed Z-flashing at the head. The Z-flashing Therma-Tru ships with Benchmark units is short by design. On Coral Springs homes with low-slope eaves, that short flashing lets wind-driven rain run behind the brickmold. We extend the flashing leg up behind the weather barrier, lap it over the original, and seal it with a urethane caulk that doesn’t chalk out in Florida heat.
• Therma-Tru sliding patio doors with track leaks after shingle replacement. When a roofer replaces shingles and leaves old step flashing in place, water finds the gap between the new shingle and the old flashing. The water follows the wall down and lands on the patio door track, where it pools and corrodes the roller assemblies. We regrade the flashing, replace the rollers, and reset the track so it drains instead of collects.
• Tile roof transitions over Therma-Tru transom windows. Coral Springs tile roofs have a transition point where the tile meets the flat wall above a transom. If the original roofer didn’t install a proper kick-out flashing, water spills down the wall and into the transom’s top glazing channel. We cut in a kick-out flashing and reseat the transom glass with new glazing tape.
• Metal roof panels with exposed fasteners above Therma-Tru doors. Metal roofing in Coral Springs expands in the heat and contracts at night. Over years, the neoprene washers on exposed fasteners dry out, shrink, and let water run down the roof deck. That water shows up at the top corners of Therma-Tru door frames. We replace the failed fasteners with oversized-headed screws and re-torque, then check the door’s head seal for any moisture that got in behind the frame.

Our Therma-Tru Shingle, Tile & Metal Roofing Process

Dale Kessler’s rule is simple: measure it right the first time, and the rest of the job takes care of itself. That’s how we approach every Therma-Tru job tied to roofing.

1. 1
   We listen first. You tell us where you see the water, when it shows up, and what you’ve tried already. We ask about the roof’s age and any recent roofing work.
2. 2
   We inspect the roof-to-wall transition. Before touching the door or window, we look at the flashing, the shingle or tile laps, and the drainage path off the eave. The failed component is usually not the door.
3. 3
   We write a fixed quote on paper. If the fix is straightforward, you’ll see the part number, the labor hours, and the total before we start. No surprises on the bill.
4. 4
   We decide OEM vs aftermarket parts with you. Therma-Tru parts for Fiber-Classic, Smooth-Star, and Benchmark lines are available, but some trim profiles have been discontinued. When OEM isn’t available, we’ll tell you and show you the aftermarket alternative before ordering.
5. 5
   We do the work and test it. We repair the flashing, replace the damaged component, and run water over the area to verify the fix. Then we register the work under our Done Right Promise.
6. 6
   We leave the site clean. You won’t find shingle scraps or old caulk tubes left behind. We treat your house the way we’d treat our own mother’s.

What Therma-Tru Shingle, Tile & Metal Roofing Costs in Coral Springs

Real numbers are more useful than vague ranges, so here’s what we’re charging in Coral Springs as of this writing.

• Re-flash a Therma-Tru entry door head with new Z-flashing: $240-$420 depending on access and whether we need to remove brickmold.
• Replace a rotted bottom rail on a Fiber-Classic door: $380-$650 including the rail, sealant, and re-shimming the slab.
• Kick-out flashing installation at a tile roof transition above a transom: $300-$520 including removing the two or three tiles needed to set the flashing properly.
• Track replacement and roller rebuild on a Therma-Tru sliding patio door after a leak: $450-$780 depending on track length and roller hardware condition.
• Full re-flash of a Therma-Tru door or window after a roof replacement: $520-$950 when we’re integrating with new roofing and need to lift shingles or tiles to get the laps right.

What moves the price: the height and pitch of the roof area, whether we need to remove tile or just lift shingles, and whether Therma-Tru still makes the trim profile you need. You’ll always know the number before we start. Call (727) 261-2215 for a free estimate, written down and specific to your house, not a ballpark.

Why Coral Springs Homeowners Call TruePane Windows & Doors for Therma-Tru Work

Dale Kessler grew up in the Ramblewood neighborhood of Coral Springs, reshimming jalousie windows with his father every summer. That’s where he learned a bad seal costs more than a good one ever would. TruePane has been fixing walls, doors, and the roof transitions above them since 2008 of combined community service, and we carry that history into every Therma-Tru job we take.

We’re an independent Therma-Tru service provider, not a franchise, and we back our work with the Done Right Promise. If the flashing isn’t shedding water, we come back and make it right, no paperwork fights. Our techs are background-checked and uniformed, and every call is answered by a live person, 24 hours a day, 7 days a week. We also service PGT, CGI, CWS, and ES Windows when the job calls for it, so if your Therma-Tru issue turns out to involve a neighboring window line, you’re still talking to the right company.

FAQs