Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterFrench & Double Doors in Coral Springs, FL | TruePane Windows & Doors
French and double doors open a home the way nothing else does. They widen a living room onto a pool deck, turn a dining room into an evening breeze, and let Florida light reach rooms that would otherwise sit in shadow. In Coral Springs, where every exterior opening gets scrutinized by wind codes and insurance inspectors, these doors have to do more than look good. They have to hold. TruePane Windows & Doors installs paired impact-rated French doors across Coral Springs with laminated glass in every lite and multi-point locking hardware, so you get the symmetry and the strength in one opening. Call (727) 261-2215 to talk through what fits your home.
Product Overview - French & Double Doors
Paired impact-rated French doors with laminated glass in every lite, symmetrical sightlines, and multi-point locking hardware for interior-to-exterior openings. That is the profile we install most often in Coral Springs, and it earns its place in Florida homes for reasons that go past aesthetics.
French doors carry more glass area than a single door, which means more glass to protect during a storm. On a non-impact door, that is a liability. On this product, every lite is laminated impact glass with a PVB interlayer, so each pane is engineered to hold in its frame under impact rather than shatter inward. The frames are aluminum or vinyl, built to stay square under wind load, and the locking hardware engages at multiple points along the active panel. You are not relying on one deadbolt at the handle.
Architecturally, these doors work in Mediterranean and coastal-style homes you see throughout Coral Springs, from the older neighborhoods off Wiles Road to newer construction west of the Sawgrass. They suit great rooms, primary suites, and any interior-to-exterior opening where you want the whole wall to feel like glass.
We sell and install this profile across our PGT, CGI, CWS, ES Windows, ECO, and Mr-Glass lines, so we can match the right frame and glass package to your wind zone and your budget.
Technical Specifications
The numbers that matter, at a glance:
- Frame materials: Aluminum or vinyl, selected by exposure and finish preference
- Maximum width: Up to 96 inches wide for the paired assembly, depending on configuration
- Glass options: Laminated impact glass (PVB interlayer), Low-E insulated glass, tinted glass, clear glass
- Finish options: White, almond, bronze, black, tan
- Design pressure: Matched to your wind zone, up to +/-100. Never higher than your zone requires.
- Hardware: Multi-point locking system on the active panel for compression and forced-entry resistance
- Compliance: Miami-Dade NOA and Florida Product Approval numbers available per configuration, engineered to FBC High-Velocity Hurricane Zone (HVHZ) requirements
Because these are paired doors rather than a single slab, the rough opening and the framing underneath both matter. We measure for both before we quote, so you are not guessing at load points or reveal widths.
Hurricane & Compliance Performance
Every product we install in Coral Springs has to earn its place on the permit, not just in the brochure. Here is what this product carries, configuration by configuration.
Laminated Impact Glass - Every lite in a French door assembly is laminated impact glass with a PVB (polyvinyl butyral) interlayer. If debris strikes, the glass may crack, but the interlayer holds the pane in the frame. That keeps the building envelope sealed while the storm passes, which is the entire point of impact-rated construction.
Miami-Dade NOA / Florida Product Approval - NOA (Notice of Acceptance) and Florida Product Approval numbers exist for each tested configuration of these doors. The number is issued per configuration, not per product line, so we verify the exact approval on your specific quote against the size, frame, and glass package you choose.
FBC / HVHZ Compliance - These doors are engineered to Florida Building Code High-Velocity Hurricane Zone requirements. Coral Springs sits in a region where HVHZ standards govern product approval, and the engineering is done to that standard from the start, not retrofitted to pass.
TAS 201 / 202 / 203 Testing Context - The protocol family behind HVHZ-rated products includes TAS 201 (large-missile impact), TAS 202 (cyclic wind-pressure loading), and TAS 203 (forced-entry resistance). These are the tests the product family is subjected to in approved configurations. We cite them so you know what the approval actually means.
Design Pressure for Your Wind Zone - Design pressures are matched to your wind zone, up to +/-100. Never higher. Pushing a higher DP rating than your zone requires adds cost without adding protection. We spec to the zone, so the door does its job and the price stays honest.
Energy Performance - Low-E and insulated glass options are available for homeowners who want the impact rating plus a cooler interior. In Coral Springs, where afternoon sun hits west-facing walls hard, a Low-E laminate can cut heat gain meaningfully. We will show you the tradeoff on the quote.
Color & Glass Options
Finish colors come in white, almond, bronze, black, and tan. White and almond read traditional and disappear into stucco walls, which suits the older Coral Springs neighborhoods where homes lean Mediterranean. Bronze and black are the choices we see more often on newer construction and modern builds, where the frame becomes a design line rather than an afterthought. Tan is a quieter earth tone that blends well with tile roofs and warm exterior palettes.
On glass, clear laminated impact glass is the standard starting point. It gives you the impact rating without altering the way natural light enters. Tinted glass reduces glare on east- and west-facing openings. Low-E insulated glass adds a thermal barrier that matters most on doors that get direct sun much of the day. We help you pick based on which way the opening faces and whether the room behind it already fights heat gain.
Installation by TruePane Windows & Doors in Coral Springs
A NOA-rated door installed incorrectly is not a NOA-rated door. The approval lives in the test configuration, and the test configuration assumes the product is anchored and sealed the way the engineering expects. That is why installation matters as much as the product itself.
Our process in Coral Springs starts with a pre-install inspection. We check the rough opening, the condition of the surrounding framing, and the existing header. You cannot hang a 96-inch paired door on a header that was never sized for it. We measure, we check level and plumb, and we note anything that will affect the installation before we start.
On install day, we set the frame level, plumb, and square. The door will not operate smoothly over time if the frame is twisted even a fraction of an inch. We seal the perimeter with AAMA 812 low-expansion foam per AAMA 2400/2410 installation practice, which keeps water and air out without distorting the frame. Then we run a water test on the threshold and sill before we call the job done.
Coral Springs permitting adds a layer most Florida cities share: your opening has to meet HVHZ product approval standards, and the permit package needs the NOA or FL Product Approval number for the exact configuration. We are used to what the building department asks for, so the paperwork moves without surprises.
Improper installation compromises the whole system. A gap in the perimeter seal or a frame set out of square voids the protection faster than a bad product ever could. That is the case for professional installation, and it is why we install every door we sell rather than handing it to a subcontractor.
Frequently Asked Questions - French & Double Doors
Design pressure is matched to your wind zone, up to +/-100, and never higher than the zone requires. Your specific rating depends on the size, glass package, and frame material. We confirm the exact DP on your quote against your property’s location in Coral Springs. Call (727) 261-2215 and we will pull the right configuration.
Lead time depends on the manufacturer line and the options you choose. Standard configurations move faster than custom sizes with a specific finish. We give you a realistic window when we quote, and we update you if it shifts. Call (727) 261-2215 for current production times on the line you are considering.
Yes, for an HVHZ-rated opening, your permit package will need the NOA or Florida Product Approval number that matches the exact configuration you install. We provide the correct approval documentation with your quote and permit submittal. The numbers are issued per configuration, so we verify against your size and glass package specifically.
You can, within the engineering limits of the product. Paired assemblies go up to 96 inches wide, and we can configure active and inactive panels differently, add sidelites where the opening allows, and choose hardware finishes. Not every custom size will carry an approval, so we confirm feasibility before you commit. Call (727) 261-2215 to discuss what is possible for your opening.
Rinse the frame with water, keep the track and threshold clear of sand and debris, and wipe down the weather seals with a mild cleaner twice a year. Coastal air carries salt that accelerates corrosion, so doors near open water or on preserve-front lots benefit from more frequent rinsing. Lubricate multi-point hardware per the manufacturer’s guidance, and check the sill drainage channels after heavy rain. If you notice a tight latch or a draft, call us before it becomes a bigger problem.
Get a Quote - French & Double Doors in Coral Springs
If you are ready to price French and double doors for your Coral Springs home, call (727) 261-2215. We will schedule a free on-site measurement, walk through your wind zone and design pressure requirements, and give you a written quote with the exact NOA or Florida Product Approval numbers for your configuration. No pressure, no guesswork, just a door that opens wide and closes tight.
Written by the team at TruePane Windows & Doors, serving Coral Springs, FL.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.
Other TruePane Windows & Doors Services
What Neighbors Say About TruePane Windows & Doors
Detailed Images
